Veris-industries E50F5 Install User Manual download pdf (Page 18)

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

Installation Guide

Power Monitoring

EF, EF

Registration Instructions

The plugin installer registered the plugin globally, but as a system level plugin, it must be registered separately for each network

that requires it. Registration can be accomplished either while opening a network or after a network is opened. Instructions here

are for the latter method.

1. Open the LonMaker network where the plugin is to be registered.

2. Select the LonMaker menu (on the toolbar in Visio 2003; under the Add-ins toolbar in Visio 2010). From the drop-down list,

select “Plugins,” and then “Register Plugins…”

3. Select the “Veris E50 Device Plug-in” entry from the plugin list and press the “Register” button.

4. Press the “Okay” button.

Device Creation Instructions

Creating an E50 device in LonMaker is no dierent than creating any other device.

1. Drag a “Device” from the LonMaker Basic Shapes stencil or other stencil to the drawing. This opens the new device wizard.

2. Click the “Commission device” checkbox unless the network is being created ONet (“Engineered” mode), or if there is any

other reason to delay commissioning.

3. From the Device Template section, choose the “VerisE50” template from the drop-down list (the plugin added the template to

the network when registering).

4. Finish customizing using the wizard prompts and press “Finish”.

5. If commissioning was selected, press the service pin on the meter.

Device Conﬁguration Instructions

The plugin has two tabs useful for conguring the device. The “Meter Setup” tab includes details related to the installation (CT

size, system type, system voltage, etc.), and other settings related to the demand interval and alarm conguration. The second

tab for conguration of the device is the “Propagation Settings” tab, which includes conguration properties that control

propagation (heartbeat, throttle, etc.). Settings can be written to both the database and the device if the device is online (or soft

oine), commissioned, and the LonMaker mode is OnNet. Otherwise the settings can only be written to the database. There is

some behavior to be noted if changes are made while the device is soft oine. Please read the “Important Information When

Conguring While Soft Oine” section below.

1. Right click on the E50 device and select “congure” from the context menu. This brings up the “Meter Setup” tab of the plugin.

2. To get the current setting from the meter or the database, press the “GET PRESENT SETTINGS” button. If the conguration

properties on the device do not match the database, a prompt appears to choose which values to load.

3. Make the necessary changes to the Installation Details and Other Settings. Note that the Demand Subinterval Length is also the

logging interval for E50F5 meters, so it can be congured at this point (see the “Conguring the Data Log” section below for a

description of the meter’s data logging capabilities).

4. Press “APPLY SETTINGS.” If the device is online (or soft oine), commissioned, and the LonMaker mode is OnNet, the

conguration property settings are applied to both the network database and the device. If, however, the above conditions

are not met, the conguration property settings are only written to the database. A dialog box appears when the write is

nished, stating where the values were written to. If values were not written to the device (database only), the device must be

resynchronized to the database at a later time. See the “Conguration Property Resynchronization” section below.

5. Switch to the “Propagation Settings” tab of the plugin (tab control is at the top of the plugin).

6. To get the current setting from the meter or the database, press the “GET PRESENT SETTINGS” button. If the conguration

properties on the device do not match the database, a prompt will appear to choose which values to load.

Using the LNS

Plugin (cont.)

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 33 34

Comments to this Manuals

No comments

Veris-industries E50F5 Install User Manual Page 18

Comments to this Manuals

Related products and manuals for Equipment Veris-industries E50F5 Install